View HT82V42_4627766.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

HT82V42 single-channel 16-bit ccd/cis analog signal processor block diagram rev. 1.20 1 december 8, 2010 features 3.3v single power supply low power consumption: 188mw (typ.) power-down mode: 300ua (typ.) 16-bit 15 msps a/d converter guaranteed won t miss codes 8-bit programmable gain correlated double sampling 315mv 8-bit programmable offset programmable clamp voltage internal voltage reference programmable 4-wire serial interface 4-bit multiplexed nibble mode 20-pin ssop/tssop package cds 10-bit dac pga + red green blue 16-bit adc bandgap reference configuration register mux register 16 : 4 mux digital control interface red green blue 16 4 gain registers offset registers od[0] od[1] od[2] dgnd dvdd2 avss vrt vrb avss avdd vin cdsclk2 dclk sdi sen sclk 3:1 mux rdac gdac bdac 3:1 mux rpga gpga bpga vrlc/ bais clamp dac od[3]/sdo vrx dvdd1 rlc/acyc general description the HT82V42 is a complete analog signal processor for ccd imaging applications. it features a 1-channel archi - tecture designed to sample and condition the outputs of tri-linear color ccd arrays. the channel consists of an input clamp, correlated double sampler (cds), offset dac and programmable gain amplifier (pga) and a high performance 16-bit a/d converter. the cds ampli- fiers may be disabled for use with sensors such as con- tact image sensors (cis) and cmos active pixel sen - sors, which do not require cds. the 16-bit digital output is available in 4-bit wide multiplexed format. the internal registers are programmed through a 4-wire serial inter - face, which provides gain, offset and operating mode adjustments. the HT82V42 operates from a single 3.3v power supply and typically consumes 188mw of power. applications flatbed document scanners film scanners digital color copiers multifunction peripherals
pin assignment pin description pin name i/o description agnd p negative power supply for analog circuit dvdd1 p digital driver power (3.3v). cdsclk2 di cds video sample clock pulse input rlc/acyc di acyc auto cycles between r, g, b inputs. dclk di adc clock. this clock is applied at n times the input pixel rate (n = 2, 3, 6, 8 or any multiple of 2 thereafter depending on input sample mode). dgnd p digital driver ground sen di serial interface enable pulse (high active) dvdd2 p digital driver power(3.3v). sdi di serial data input sck di clock input for serial interface od0~od2 od3/sdo do digital multiplexed output data bus. adc output data d[15:0] is available in two multiplexed formats as shown. when address bit4 = 1 and sen has been pulsed high, this pin use as sdo for register data read-back. otherwise, this pin use as digital data output. avdd p analog supply (3.3v). vrb ao reference decoupling, this pin must be connected to agnd via a decoupling capacitor. vrt ao reference decoupling, this pin must be connected to agnd via a decoupling capacitor. vrx ao reference decoupling, this pin must be connected to agnd via a decoupling capacitor. vrlc/vbias ao selectable analog output voltage for rlc or single-ended bias reference. this pin would typi - cally be connected to agnd via a decoupling capacitor. vrlc can be externally driven if pro - grammed hi-z. vin ai analog input note: ai=analog input; ao=analog output; aio=analog inout di=digital input; do=digital output; p=power HT82V42 rev. 1.20 2 december 8, 2010

abcd d12 d8 d4 d0 d13 d9 d5 d1 d14 d10 d6 d2 d15 d11 d7 d3
absolute maximum ratings supply voltage ..........................v ss 0.3v to v ss +4.3v storage temperature ........................... 50 cto125 c input voltage .............................v ss 0.3v to v cc +0.3v operating temperature ..............................0 cto70 c analogue supply power ...............................3.0v~3.6v digital supply power......................................3.0v~3.6v note: these are stress ratings only. stresses exceeding the range specified under absolute maximum ratings may cause substantial damage to the device. functional operation of this device at other conditions beyond those listed in the specification is not implied and prolonged exposure to extreme conditions may affect device reliability. d.c. characteristics av dd =dv dd1 =dv dd2 =3.3v, agnd=dgnd=0v, ta=25 c, dclk=30mhz unless otherwise stated. symbol parameter test conditions min. typ. max. unit v dd conditions overall system specification (including 16-bit adc, pga, offset and cds functions) full-scale input voltage range (see note 1) 3.3v 0.27 v p-p 3.0 v p-p v in input signal limits (see note 2) 3.3v 0 av dd v full-scale transition error 3.3v gain = 0db; pga[7:0] = 54(hex) 50 mv zero-scale transition error 3.3v gain = 0db; pga[7:0] = 54(hex) 50 mv dnl differential non-linearity 3.3v 1.5 lsb inl integral non-linearity 3.3v 50 lsb total output noise 3.3v min gain 7 lsb rms max gain 18 references vrt upper reference voltage 1.90 2.00 2.20 v vrb lower reference voltage 0.90 1.00 1.20 v vrx input return bias voltage 1.70 v v rtb diff. reference voltage (vrt-vrb) 0.9 1.0 1.1 v reset-level clamp (rlc) circuit/ reference level dac reference rlcdac resolution 4 bits v rlcstep reference rlcdac step size rlcdacrng=0 3.3v 0.159 0.173 0.187 v/step v rlcbot reference rlcdac step size rlcdacrng=1 0.096 0.11 0.124 v/step v rlcbot reference rlcdac output voltage at code 0(hex), rlcdacrng=0 3.3v 0.35 0.4 0.45 v v rlctop reference rlcdac output voltage at code 0(hex), rlcdacrng=1 0.35 0.40 0.45 v HT82V42 rev. 1.20 3 december 8, 2010
symbol parameter test conditions min. typ. max. unit v dd conditions v rlctop reference rlcldac output voltage at code f(hex), rlcdacrng=0 3.3v 2.8 3.0 3.10 v v rlcstep reference rlcdac output voltage at code f(hex), rlcdacrng=1 1.90 2.00 2.10 v offset dac, monotonicity guaranteed resolution 8 bits dnl differential non-linearity 0.1 0.5 lsb inl integral non-linearity 0.25 1.00 lsb step size 2.46 mv/step output voltage 315 mv +315 mv programmable gain amplifier resolution 8 bits gain equation 186/(278-pga[7:0]) v/v g max max gain 6.50 8.00 8.40 v/v g min min gain 0.65 0.68 0.75 v/v gain error 2 % analogue to digital converter resolution 16 bits speed 15 msps full-scale input range (2*(vrtvrb)) 2 v digital inputs v ih high level input voltage 0.7v dd v v il low level input voltage 0.2v dd v i ih high level input current 1 a i il low level input current 1 a c i input capacitance 5 pf digital outputs v oh high level output voltage i oh =1ma dv dd -0.5 v v ol low level output voltage i ol =1ma 0.5 v i oz high impedance output current 1 a supply currents total supply current active (signal channel mode) linebyline=1 dclk=30mhz 57 ma total analog supply current active (signal channel mode) linebyline=1 dclk=30mhz 36 ma digital supply current active (dv dd1 ) dclk=30mhz 14 ma HT82V42 rev. 1.20 4 december 8, 2010
symbol parameter test conditions min. typ. max. unit v dd conditions digital supply current active (dv dd2 ) dclk=30mhz 7 ma supply current full power down mode 300 a note: 1. full-scale input voltage denotes the peak input signal amplitude that can be gained to match the adc full-scale input range. 2. input signal limits are the limits within which the full-scale input voltage signal must lie. a.c. characteristics av dd =dv dd1 =dv dd2 =3.3v, agnd=dgnd=0v, ta=25 c, dclk=30mhz unless otherwise stated. symbol parameter test conditions min. typ. max. unit v dd conditions conversion rate 3.3v 15 msps input video timing av dd =dv dd1 =dv dd2 =3.3v, agnd=dgnd=0v, ta=25 c, dclk=30mhz unless otherwise stated. symbol parameter min. typ. max. unit t per dclk period 33.3 ns t dclkh dclk high period 16.6 ns t dclkl dclk low period 16.6 ns t vsmpsu cdsclk2 setup time 6 ns t vsmph cdsclk2 hold time 3 ns t vsu video level setup time 10 ns t vh video level hold time 3 ns t rsu reset level setup time 10 ns t rh reset level setup time 3 ns note : 1. t vsu and t rsu denote the setup time require after the input video signal has settled. 2. parameters are measured at 50% of the rising/falling edge. HT82V42 rev. 1.20 5 december 8, 2010
output data timing av dd =dv dd1 =dv dd2 =3.3v, agnd=dgnd=0v, ta=25 c, dclk=30mhz unless otherwise stated. symbol parameter min. typ. max. unit t pd output propagation delay 16 ns av dd =dv dd1 =dv dd2 =3.3v, agnd=dgnd=0v, ta=25 c, dclk=30mhz unless otherwise stated. symbol parameter min. typ. max. unit t cycsu auto cycle setup time 6 ns t acych auto cycle hold time 3 ns HT82V42 rev. 1.20 6 december 8, 2010 output data timing auto cycle timing
serial interface av dd =dv dd1 =dv dd2 =3.3v, agnd=dgnd=0v, ta=25 c, dclk=30mhz unless otherwise stated. symbol parameter min. typ. max. unit t sper sck period 37.6 ns t sckh sck high 18.8 ns t scklz sck low 18.8 ns t ssu sdi setup time 6 ns t sh sdi hold time 6 ns t sce sck to sen setup time 12 ns t sec sen to sck setup time 12 ns t sew sen pulse width 25 ns t serd sen low to sdo = register data 30 ns t scrd sck low to sdo = register data 30 ns t scrdz sck low to sdo = adc data 30 ns note: parameters are measured at 50% of the rising/falling edge. HT82V42 rev. 1.20 7 december 8, 2010 serial interface timing
HT82V42 rev. 1.20 8 december 8, 2010 system architecture introduction a device block diagram showing the signal paths pres - ent is provided. the HT82V42 samples a single channel input v in . the device then processes the sampled video signal with respect to the video reset level or an inter - nally/externally generated reference level for signal pro - cessing. the processing channel consists of an input sampling block with optional reset level clamping (rlc) and correlated double sampling (cds), an 8-bit programmable offset dac and an 8-bit programmable gain amplifier (pga). the adc then converts this ana - logue signal to a 16-bit digital word. the digital output from the adc is presented on a 4-bit wide bus. on-chip control registers determine the configuration of the de - vice, including the offsets and gains applied to r/g/b signal. these registers are programmable via a serial interface. input sampling the HT82V42 can sample and process the input ana - logue signals as follows: monochrome a single chosen input vin is sampled, processed by the corresponding channel, and converted by the adc. the choice of input can be changed via the con- trol interface, e.g. on a line-by-line basis if required. colour line-by-line a single chosen input (red, green and blue) is sam - pled and multiplexed into the analogue channel for processing before being converted by the adc. the input selected can be switched in turn (red
green
blue
red ) together with the pga and offset dac control registers by pulsing the rlc/acyc pin. this is known as auto-cycling. alternatively, other sampling sequences can be generated via the control registers. refer to the line-by-line operation section for more details. clamp voltage the device contains an integrated single 4-bit dac which is controlled by register setting for the clamp volt - age. the internal clamp is sampled on the positive edge of dclk that occurs during each cdsclk2 pulse. the sampled level, high (or low) controls the presence (or absence) of the internal cl pulse on the next reset level. the position of cl can be adjusted by using control bits cdsref[1:0]. reset sample and clamp timing
HT82V42 rev. 1.20 9 december 8, 2010 cds/cis processing for ccd type input signals, the time at which the reset level is sampled, is adjustable by setting control bits cdsref[1:0] as shown in the previous figure. for cis type input signals, non-cds processing is used. during this case, the video level is processed with the voltage level on vrlc/vbias, the pin vrlc/vbias is generated internally or externally. the vrlc/vbias is sampled by rs at the same time as vs samples the video level in this mode. pga gain registers there are three pga registers which are used to individ - ually program the gain. bits d7 through d0 control the gain range in 256 increments. see the figure for a graph of the pga gain versus pga register code. the coding for the pga registers is a straight binary number, with all zero words corresponding to the minimum gain setting (0.68x) and all one words corresponding to the maxi - mum gain setting (8x). the pga has a gain range from 0.68x (-3.3db) to 8x (18db), adjustable in 256 steps. the figure shows the pga gain as a function of the pga register code. al - though the gain curve is approximately linear in db, the gain in v/v varies in nonlinear proportion with the regis - ter code, according to the following the equation: gain (v/v) = 186 / (278-pga[7:0]) gain (db) = 20log 10 (186/(278-pga[7:0])) d7 d6 d5 d4 d3 d2 d1 d0 gain(v/v) gain (db) msb lsb 00000000 0.68 -3.3 0101110010* 11000000 2.23 7 11100000 3.50 10.8 11111111818 note: * power-on default value pga gain register settings
HT82V42 rev. 1.20 10 december 8, 2010 offset registers there are three offset registers used to individually program the offset. bits d7 through d0 control the offset range from -315mv to 315mv in 256 increments. the table shows the offset range as a function of the bits d7 through d0. d7 d6 d5 d4 d3 d2 d1 d0 offset (mv) msb lsb 00000000 -315 : : : : 10000000*0 : : : : 11111111 +315 note :*power-on default value offset register settings adc input black level adjust the output from the pga should be offset to match the full-scale range of the adc (vfs=2.0v). for nega - tive-going input video signals, a black level (zero differ - ential) output from the pga should be offset to the top of the adc range by setting register bits pgafs[1:0]=10. for positive going input signal the black level should be offset to the bottom of the adc range by setting pgafs[1:0]=11. bipolar input video is accommodated by setting pgafs[1:0]=00 or pgafs[1:0]=01 (zero dif- ferential input voltage gives mid-range adc output). overall signal flow summary the input sampling block produces an effective input voltage v1. for cds, this is the difference between the input video level vin and the input reset level vreset. for non-cds this is the difference between the input video level vin and the voltage on the vrlc/vbias pin, vvrlc, optionally set via the rlc dac. the offset dac block then adds the amount of fine offset adjustment required to move the black level of the input signal towards 0v, producing v2. the pga block then amplifies the white level of the input signal to maximise the adc range, outputting voltage v3. the adc block then converts the analogue signal, v3, to a 16-bit unsigned digital output, d1. the digital output is then inverted, if required, through the output invert block to produce d2. calculating output for any given input the following equations describe the processing of the video and reset level signals through the HT82V42. the values of v1, v2 and v3 are often calculated in reverse order during device setup. the pga value is written first to set the input voltage range, the offset dac is then adjusted to compensate for any black/reset level off - sets and finally the rlc dac value is set to position the reset level correctly during operation. overall signal flow
HT82V42 rev. 1.20 11 december 8, 2010 input sampling block: input sampling and referencing if cds = 1, (i.e. cds operation) the previously sampled reset level, vreset, is subtracted from the input video. v1 = vin - vreset...................................................................eqn. 1 if cds = 0, (non-cds operation) the simultaneously sampled voltage on pin vrlc is subtracted instead. v1 = vin - vvrlc .....................................................................eqn. 2 if vrlcext = 1, vvrlc is an externally applied voltage on pin vrlc/vbias. if vrlcext = 0, vvrlc is the output from the internal rlc dac. vvrlc = (vrlcstep rlcv[3:0]) + vrlcbot....................eqn. 3 vrlcstep is the step size of the rlc dac and vrlcbot is the minimum output of the rlc dac. offset dac block: offset (black - level) adjust the resultant signal v1 is added to the offset dac output. v2 = v1 + { 315mv (dac[7:0] - 127.5) } / 127.5.....................eqn. 4 pga node: gain adjust the signal is then multiplied by the pga gain, v3=v2 [186 / (278 - pga[7:0] ) ]...........................................eqn. 5 adc block: analogue-digital conversion the analogue signal is then converted to a 16-bit unsigned number, with input range configured by pgafs[1:0]. d1[15:0] = int{ (v3 /vfs) 65535} + 32767 pgafs[1:0] = 00 or 01 .................eqn. 6 d1[15:0] = int{ (v3 /vfs) 65535} pgafs[1:0] = 11 ..........................eqn. 7 d1[15:0] = int{ (v3 /vfs) 65535} + 65535 pgafs[1:0] = 10 ..........................eqn. 8 where the adc full-scale range, vfs = 2.0v if d1[15:0] < 0 d1[15:0] = 0 if d1[15:0] > 65535 d1[15:0] = 65535 output invert block: polarity adjust the polarity of the digital output may be inverted by control bit invop. d2[15:0] = d1[15:0] (invop = 0).....................................................eqn. 9 d2[15:0] = 65535 - d1[15:0] (invop = 1)...................................................eqn. 10 output formats latency of valid output data with respect to cdsclk2 is programmable by writing to control bits del[1:0]. the latency for each mode is shown in the operating mode timing diagrams section. figure shows the output data formats for modes 1, 3 and 4. figure shows the output data formats for mode 2. table summarizes the output data obtained for each format. output format output pins output 4+4+4+4-bit (nibble) od3~od0 a= d15~d12 b= d11~d8 c= d7~d4 d= d3~d0 details of output data

! " # " $ # " output data formats (mode 2)

! " # " $ # " output data formats (mode 1, 3, 4)
HT82V42 rev. 1.20 12 december 8, 2010 control interface the internal control registers are programmed via the serial digital control interface. the register contents can be read back via the serial interface on pin od3/sdo. it is recommended that a software reset is carried out after the power-up sequence, before writing to any other reg - ister. this ensures that all registers are set to their de - fault values serial interface register write figure shows the register writing in serial mode. three pins, sck, sdi and sen are used. a six-bit address (a5, a4, a3, a2, a1, a0) is clocked in through sdi, msb first, followed by an eight-bit data word (b7, b6, b5, b4, b3, b2, b1, b0), also msb first. each bit is latched on the ris - ing edge of sck. when the data has been shifted into the device, a pulse is applied to sen to transfer the data to the appropriate internal register. note all valid regis - ters have address bit a4 equal to 0 in the write mode. a software reset is carried out by writing to address 000100 with any value of data, i.e. data word = xxxxxxxx. serial interface register read-back figure shows register read-back in serial mode. read-back is initiated by writing to the serial bus as de- scribed above but with address bit a4 set to 1, followed by an 8-bit dummy data word. writing address (a5, 1, a3, a2, a1, a0) will cause the contents (d7, d6, d5, d4, d3, d2, d1, d0) of the corresponding register (a5, 0, a3, a2, a1, a0) to be output msb first on pin sdo (on the falling edge of sck). note that pin sdo is shared with an output pin, od3. it must be noted that when reading from a register the od3 pin function will be disabled and cannot be read by the external mcu. the next word may be read in to sdi while the previous word is still be - ing output on sdo. timing requirement to use this device a master clock (dclk) of up to 30mhz and a per-pixel synchronisation clock (cdsclk2) of up to 15mhz are required. these clocks drive a timing control block, which produces internal sig - nals to control the sampling of the video signal. the dclk to cdsclk2 ratios and maximum sample rates for the various modes are shown in table. programmable cdsclk2 detect circuit the cdsclk2 input is used to determine the sampling point and frequency of the HT82V42. under normal op - eration a pulse of 1 dclk period should be applied to cdsclk2 at the desired sampling frequency (as shown in the operating mode timing diagrams) and the input sample will be taken on the first rising dclk edge after csdclk2 has gone low. however, in certain applica - tions such a signal may not be readily available. the programmable cdsclk2 detect circuit in the HT82V42 allows the sampling point to be derived from any signal of the correct frequency, such as a ccd shift register clock, when applied to the cdsclk2 pin. when en- abled, by setting the vsmpdet control bit, the circuit detects either a rising or falling edge (determined by the posnneg control bit) on the cdsclk2 input pin and generates an internal vsmp pulse. this pulse can op- tionally be delayed by a number of dclk periods, speci- fied by the vdel[2:0] bits. figure shows the internal vsmp pulses that can be generated by this circuit for a typical clock input signal. the internal vsmp pulse is then applied to the timing control block in place of the normal cdsclk2 pulse provided from the input pin. the sampling point then occurs on the first rising dclk edge after this internal vsmp pulse, as shown in the op - erating mode timing diagrams. serial interface register write serial interface register read-back
HT82V42 rev. 1.20 13 december 8, 2010 internal vsmp pulse generated by programmable internal sample detect circuit references the adc reference voltages are derived from an inter- nal bandgap reference, and buffered to pins vrt and vrb, where they must be decoupled to ground. pin vrx is driven by a similar buffer, and also requires de - coupling. the output buffer from the rlcdac also re - quires decoupling at pin vrlc/vbias. power supply the HT82V42 can run from a single 3.3v single supply. power management power management for the device is performed via the control interface. the device can be powered on or off completely by clearing the en bit low. all the internal registers maintain their previously pro - grammed value in the power down mode while the se - rial interface inputs remain active. line-by-line operation certain linear sensors (e.g. contact image sensors) give a colour output on a line-by-line basis. i.e. a full line of red pixels followed by a line of green pixels followed by a line of blue pixels. in this mode the input multiplexer and (optionally) the pga/offset register multiplexers can be auto-cycled by the application of pulses to the rlc/acyc input pin by setting the acycnrlc register bit. see figure for de - tailed timing information. the multiplexers change on the first dclk rising edge after rlc/acyc is taken high. a write to the auto-cycle reset register causes these multiplexers to be reset, selecting the colour r and the red offset/gain registers. alternatively, all three multiplexers can be controlled via the serial interface by writing to register bits intm[1:0] to select the desired colour. it is also possible for the input multiplexer to be controlled separately from the pga and offset multiplexers. table describes all the multiplexer selec - tion modes that are possible.
HT82V42 rev. 1.20 14 december 8, 2010 acycnrlc name description 0 internal no force mux input mux, offset and gain registers determined by internal register bits intm1, intm0. 1 auto-cycling, no force mux input mux, offset and gain registers auto-cycled, rinp
ginp
binp
rinp on rlc/acyc pulse. colour selection description in line-by-line mode operating modes mode description cds max. sample rate sensor interface description timing requirement register contents with cds register contents without cds 1 monochrome/colour line-by-line yes 5 msps only one input channel at a time is continuously sampled. dclk = 30mhz dclk: cdsclk2 ratio is 6:1 setreg1 : 3f(h) setreg1: 2d(h) 2 fast monochrome/ colour line-by-line yes 10 msps identical to mode 1 dclk = 30mhz dclk: cdsclk2 ratio is 3:1 identical to mode 1 plus setreg3: bits 5:4 must be set to 0 (h) identical to mode 1 3 maximum speed monochrome/colour line-by-line no 15 msps identical to mode 1 dclk = 30mhz dclk: cdsclk2 ratio is 2:1 cds not possible setreg1: 6d(h) 4 slow monochrome/ colour line-by-line yes 3.75 msps identical to mode 1 dclk = 30mhz dclk: cdsclk2 ratio is 2n:1, n>=4 identical to mode 1 identical to mode 1 HT82V42 operating modes operating mode timing diagrams the following diagrams show 4-bit multiplexed output data and dclk, cdsclk2 and input video requirements for most common operations as shown in table. mode 1 operation
HT82V42 rev. 1.20 15 december 8, 2010 mode 2 operation mode 3 operation mode 4 operation
HT82V42 rev. 1.20 16 december 8, 2010 device configuration register map the following table describes the location of each control bit used to determine the device operation. the register map is programmed by writing the required codes to the appropriate address via the serial interface. address description def (h) r/w bit 76 5 43210 000001 setup reg 1 0f r/w 0 mode3 pgafs[1] pgafs[0] 1 1 cds en 000010 setup reg 2 23 r/w del[1] del[0] rlcdacrng 0 vrlcext invop 1 1 000011 setup reg 3 1f r/w 0 0 cdsref[1] cdsref[0] rlvc[3] rlvc[2] rlvc[1] rlvc[0] 000100 software reset 00 000101 auto-cycle reset 00 000110 setup reg 4 05 r/w 0 0 intm[1] intm[0] rlcint 1 acycnrlc linebyline 000111 revision number 41 r 001000 setup reg 5 00 r/w 0 0 0 psenneg vdel[2] vdel[1] vdel[0] vsmpdet 001001 setup reg 6 00 r/w clkmotr 0 0 00000 001010 reserved 01 r 0 0 0 00000 001011 reserved 01 r 0 0 0 00000 001100 reserved 01 r 0 0 0 00000 100000 red offset value 80 r/w ro[7] ro[6] ro[5] ro[4] ro[3] ro[2] ro[1] ro[0] 100001 green offset value 80 r/w go[7] go[6] go[5] go[4] go[3] go[2] go[1] go[0] 100010 blue offset value 80 r/w bo[7] bo[6] bo[5] bo[4] bo[3] bo[2] bo[1] bo[0] 100011 rgb offset value 80 r/w rgbo[7] rgbo[6] rgbo[5] rgbo[4] rgbo[3] rgbo[2] rgbo[1] rgbo[0] 101000 red pga gain 5c r/w rpga[7] rpga[6] rpga[5] rpga[4] rpga[3] rpga[2] rpga[1] rpga[0] 101001 green pga gain 5c r/w gpga[7] gpga[6] gpga[5] gpga[4] gpga[3] gpga[2] gpga[1] gpga[0] 101010 blue pga gain 5c r/w bpga[7] bpga[6] bpga[5] bpga[4] bpga[3] bpga[2] bpga[1] bpga[0] 101011 rgb pga gain 5c w rgbpga[7] rgbpga[6] rgbpga[5] rgbpga[4] rgbpga[3] rgbpga[2] rgbpga[1] rgbpga[0]
HT82V42 rev. 1.20 17 december 8, 2010 register map description register bit no. bit name por description setup register 1 0en 1 0: complete power down 1: fully active 1 cds 1 select correlated double sampling mode. 0: non-cds mode 1: cds mode 2 reserved 1 default 1 3 reserved 1 default 1 5~4 pgafs[1:0] 0 adjust pga output to optimize the adc range for different po - larity sensor output signals. zero differential pga input signal gives. 00: zero output (use for bipolar video) 01: zero output 10: full-scale positive output (use for negative going video) 11: full-scale negative output (use for positive going video) 6 mode3 0 mode3 setting 1: mode3 enable setup register 2 2 invop 0 digitally inverts the polarity of output data 0: negative going video gives negative going output 1: negative going video gives positive going output 3 vrlcext 0 setting this bit high, changes vrlc/vbias to hi-z, allowing vrlc/vbias to be driven from an external power source. 5 rlcdacrn g 1 sets the output range of the rlcdac. 0: rlcdac ranges from 0 to avdd. 1: rlcdac ranges from 0 to vrt 7~6 del[1:0] 00 sets the output latency for the adc clock periods. 1 adc clock=2 dclk periods. under mode3, 1 adc clock=3 dclk periods. 00: minimum latency 01: delay by 1 adc clock 10: delay by 2 adc clock 11: delay by 3 adc clock setup register 3 3~0 rlvc[3:0] 1111 controls rlcdac driving the vrlc pin defines the single ended signal reference voltage or reset level clamp volt - age. refer to the electrical characteristic section for details. 5~ cdsref[1:0] 01 adjust reset timing under cds mode 00: advance 1 dclk period 01: normal 10: retard 1 dclk 11: retard 2 dclk 7~6 reserved 00 reserved software reset any write to this register will cause all functions to be reset. it is recommended to execute a software reset after each power on reset and before any other register writes. when this regis - ter is written, the reset function will be initiated immediately by an internal reset signal. if the dclk exists, the internal reset signal will keep active for about 2 dclk cycles. otherwise, the device will keep in reset state all the time.
HT82V42 rev. 1.20 18 december 8, 2010 register bit no. bit name por description auto-cycle reset writing to this register will cause the auto-cycle counter to be reset to colour r. this function is only required when linebyline=1. when this register is written, the reset func - tion will be initiated immediately by an internal reset signal. if the dclk exists, the internal reset signal will keep active for about 2 dclk cycles. otherwise, the device will keep in reset state all the time. setup register 4 0 linebyline 1 select line by line mode 0: normal operation 1: line by line operation 1 acycnrlc 0 when linebyline=0, this bit has no effect when linebyline=1, this bit controls the function of the rlc/acyc input signal and will control the multiplexer of the offset/gain register. 0: rlc/acyc pin enabled for reset level clamp, internal se - lection of input and offset/gain multiplexers. 1: auto cycling enabled by pulsing the rlc/acyc input pin. 3 rlcint 0 this bit is used to determine whether the reset level clamping is used. 0: rlc disable 1: rlc enable 5~4 intm[1:0] 00 colour selection bits used for internal modes. 00: red 01: green 10: blue 11: reserved setup register 5 0 vsmpdet 0 0: normal operation, signal on the cdsclk2 input pin is ap- plied directly to the timing control block 1: programmable cdsclk2 detect circuit is enabled. an in- ternal synchronization pulse is generated from the signal applied to the cdsclk2 input pin and is applied to the timing control block. 3~1 vdel[2:0] 000 when vsmpdel=0, these bits have no effect. when vsmpdel=1, these bits set the programmable delay from the detected edge of the signal on cdsclk2. the inter - nal generated pulse is delayed by vdel dclk periods from the detected edge. 4 posnneg 0 when vsmpdel=0, this bit has no effect when vsmpdel=1, this bit controls whether positive or neg - ative edges are detected. 0: negative edge on the cdsclk2 pin is detected and used to generate an internal timing pulse 1: positive edge on the cdsclk2 pin is detected and used to generate an internal timing pulse setup register 6 7 clkmotr 0 internal clock monitor. 0: normal active, od[3:0] output adc data. 1: internal clock test mode. pin clkmotr=0 clkmotr=1 od3 od3 intvsmp od2 od2 video sample clock od1 od1 adc clock od0 od0 reset sample clock
application circuits recommended external components note: 1. all capacitors should be located as close to the HT82V42 as possible. 2. agnd and dgnd should be connected as close to the HT82V42 as possible. HT82V42 rev. 1.20 19 december 8, 2010 register bit no. bit name por description red offset value 7~0 ro 80 red offset value green offset value 7~0 go 80 green offset value blue offset value 7~0 bo 80 blue offset value rgb offset value 7~0 rgbo 80 writing to this register will overwrite the new value to the r/g/b offset value red pga gain 5~0 rpga 5c red pga value green pga gain 5~0 gpga 5c green pga value blue pga gain 5~0 bpga 5c blue pga value rgb pga gain 5~0 rgbpga 5c writing to this register will overwrite the new value to the r/g/b pga gain value
package information 20-pin ssop (209mil) outline dimensions mo-150 symbol dimensions in inch min. nom. max. a 0.291 0.323 b 0.197 0.220 c 0.009 0.013 c 0.272 0.295 d 0.079 e 0.026 f 0.002 g 0.022 0.037 h 0.004 0.008 08 symbol dimensions in mm min. nom. max. a 7.40 8.20 b 5.00 5.60 c 0.22 0.33 c 6.90 7.50 d 2.00 e 0.65 f 0.05 g 0.55 0.95 h 0.09 0.21 08 HT82V42 rev. 1.20 20 december 8, 2010 % & '
20-pin tssop outline dimensions symbol dimensions in inch min. nom. max. a 0.041 0.047 a1 0.002 0.006 a2 0.037 0.041 b 0.009 c 0.005 0.007 d 0.252 0.260 e 0.248 0.256 e1 0.169 0.177 e 0.026 l 0.018 0.030 y 0.004 08 symbol dimensions in mm min. nom. max. a 1.05 1.20 a1 0.05 0.15 a2 0.95 1.05 b 0.22 c 0.13 0.17 d 6.40 6.60 e 6.30 6.50 e1 4.30 4.50 e 0.65 l 0.45 0.75 y 0.10 08 HT82V42 rev. 1.20 21 december 8, 2010 ( ) * + ,
* -
product tape and reel specifications reel dimensions ssop 20n (209mil) symbol description dimensions in mm a reel outer diameter 330.01.0 b reel inner diameter 100.01.5 c spindle hole diameter 13.0 +0.5/-0.2 d key slit width 2.00.5 t1 space between flange 16.8 +0.3/-0.2 t2 reel thickness 22.20.2 tssop 20l symbol description dimensions in mm a reel outer diameter 330.01.0 b reel inner diameter 100.01.5 c spindle hole diameter 13.0 +0.5/-0.2 d key slit width 2.00.5 t1 space between flange 16.4 +0.3/-0.2 t2 reel thickness 19.1 max. HT82V42 rev. 1.20 22 december 8, 2010
carrier tape dimensions ssop 20n (209mil) symbol description dimensions in mm w carrier tape width 16.0 +0.3/-0.1 p cavity pitch 12.00.1 e perforation position 1.750.10 f cavity to perforation (width direction) 7.50.1 d perforation diameter 1.5 +0.1/-0.0 d1 cavity hole diameter 1.50 +0.25/-0.00 p0 perforation pitch 4.00.1 p1 cavity to perforation (length direction) 2.00.1 a0 cavity length 7.10.1 b0 cavity width 7.20.1 k0 cavity depth 2.00.1 t carrier tape thickness 0.300.05 c cover tape width 13.30.1 tssop 20l symbol description dimensions in mm w carrier tape width 16.00.3 p cavity pitch 8.00.1 e perforation position 1.750.10 f cavity to perforation (width direction) 7.50.1 d perforation diameter 1.5 +0.1/-0.0 d1 cavity hole diameter 1.5 +0.1/-0.0 p0 perforation pitch 4.00.1 p1 cavity to perforation (length direction) 2.00.1 a0 cavity length 6.80.1 b0 cavity width 6.90.1 k0 cavity depth 1.60.1 t carrier tape thickness 0.300.05 c cover tape width 13.30.1 HT82V42 rev. 1.20 23 december 8, 2010 . / . . % " * $ 0 1 2 0 3 ( * $ ! 4 * * 0 4 5 * " 6 ( * 7 ( ( 8 * 6 9 8 ( : 0 7 ( * 8 9 1 0 " ( 5 * 9 4 * " 6 ( * : 0 ; ( * : ! 5 ( + ( ( 8 * ' 9 8 (
HT82V42 rev. 1.20 24 december 8, 2010 copyright 2010 by holtek semiconductor inc. the information appearing in this data sheet is believed to be accurate at the time of publication. however, holtek as - sumes no responsibility arising from the use of the specifications described. the applications mentioned herein are used solely for the purpose of illustration and holtek makes no warranty or representation that such applications will be suitable without further modification, nor recommends the use of its products for application that may present a risk to human life due to malfunction or otherwise. holtek s products are not authorized for use as critical components in life support devices or systems. holtek reserves the right to alter its products without prior notification. for the most up-to-date information, please visit our web site at http://www.holtek.com.tw. holtek semiconductor inc. (headquarters) no.3, creation rd. ii, science park, hsinchu, taiwan tel: 886-3-563-1999 fax: 886-3-563-1189 http://www.holtek.com.tw holtek semiconductor inc. (taipei sales office) 4f-2, no. 3-2, yuanqu st., nankang software park, taipei 115, taiwan tel: 886-2-2655-7070 fax: 886-2-2655-7373 fax: 886-2-2655-7383 (international sales hotline) holtek semiconductor inc. (shenzhen sales office) 5f, unit a, productivity building, no.5 gaoxin m 2nd road, nanshan district, shenzhen, china 518057 tel: 86-755-8616-9908, 86-755-8616-9308 fax: 86-755-8616-9722 holtek semiconductor (usa), inc. (north america sales office) 46729 fremont blvd., fremont, ca 94538, usa tel: 1-510-252-9880 fax: 1-510-252-9885 http://www.holtek.com

▲Up To Search▲

Price & Availability of HT82V42

	To Download HT82V42 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .